Catskill-craftsmen 51843 Manuale Utente

Assembly InstructionsModel 51843Butcher Block Island with Flat Doors and Drop LeafGENERAL:1. You have purchased model 51843. This unit is ready to ass

1 3/4” BoltsWasherNutSTEP 8Door AssemblyA. Make sure washers are placed on the pins at the bottom of the doors, then slide the doors down into t

No pilot holes as softwood. 5/8” Pan Head ScrewsSTEP 9Magnet A. Stick magnet to magnet plate on a door.B. With all other doors open, close the door. T

STEP 10Install CastersInstall Casters: Locking wheels normally go on the front. Tap in wheel sleeves until teeth bite wood. Don’t atten or wheel stem

STEP 11Towel Bar and Spice RackDecide which side to put the spice rack on then put the towel bar on the other side.Attach side handle/towel bar using

STEP 12Insert Bottom ShelfInstall Divider Panel A. Tap eight 1” pins (4 pairs of 2) into back panel.B. Tap one 1” pin into the holes beside the two

1” Pin2” PinMake sure you put the pins in the side panel at the same height as the pins in the Divider Panel 1” pinEdge Banding OutSlide Divider Panel

5/8” #8 Marking an X with a pencil on the pi-lot holes under the tabletop will help to line up the pilot holes with the L Brackets in step 14.STEP 13

STEP 14Fasten the table top with 5/8” #7 screws up through the “L” Brackets.5/8” #7

5/8” wooden diskSTEP 15A. Slide panels into place on pins with edge banding out.B. Re-tighten screws and tap wooden 5/8” plugs into holes in legs.C.

For continued beauty and long life of your Catskill Craftsmen cart, we recommend Catskill Craftsmen’s Butcher Block Oil. Our Butcher Block Oil is avai

Parts List Model 51843Drawer Front (1)P/N DF-51843Drawer Back (1)P/N DBK-51843Right Drawer Side (1)P/N DS-51843/RLeft Drawer Side (1)P/N DS-51843/LGli

Side Panel (2)P/N SP-51843 Bottom Shelf (1)P/N BS-51843Table Top (1)P/N TT-51843Drop Leaf (1)P/N DL-51843Back Panel (1)P/N BP-5184329 3/4”

Hardware for 518431 3/4” Phillips Flat Head Bolt (8) 1 1/4” Phillips Flat Head #8 Screw (16) 7/8” Truss Head Machine Screw (12) 5/8” Pan Head Screw (6

7/8” Truss Head Screw1/2” #4 Flat Head Screw5/8” #81” Pin3/4” PinThe counter sunk hole goes out so the bumps go toward the wood.1 1/2” PinFlush at bot

STEP 4 A. Attach the Drawer Back to the Drawer Sides with two 1 1/2” #8 screws. There are left and right drawer sides. Make sure the slots that run th

WRONG!Post needs to be screwed deeper.WRONG!Post needs to be backed out.CORRECT!Set screw secures post properly.Step 1 1. The Bastion fastening syste

STEP 5 A. Attach a Glide Support Stick to the top of each Side Panel using 1 1/4” #8 screws. The countersunk holes (reamed out) in the stick are posit

STEP 6 A. Lay Back Panel at on a smooth surface with holes up.B. Attach Side Panels with 1 3/4” machine screws (bolts) and hex nuts. After inserting